Lumasense-technologies M390S Manuel d'utilisateur

MANUA LM390SBlackbody Calibration Source

M390S Manual Introduction  102.2 Technical DataThis Model Model Temperature Range[ ] M390-S 600 to 3000 °C (1110 to 5430 °F) Custom split designAc

M390S Manual Installation  113 Installation3.1 Installing the M390STo install the M390S:1. Allow the M390 to warm-up to room temperature for at leas

M390S Manual Installation  12To ensure consistent document formatting, this page was intentionally left blank.

M390S Manual Operation  134 Operation4.1 Starting UpTo start up the M390S:1. Turn on the power switch/breaker and allow 20 seconds for the system to

M390S Manual Operation  14Eurotherm controller4.2.1 Other Controller ModesIf, for some reason, the power must be turned off while monitoring tempera

M390S Manual Operation  159. Press the PAGE button until ACCESS appears.10. Press the SCROLL button.11. Press the DOWN button until LEVEL 1 appears

M390S Manual Operation  164.5.1 RS485 OptionRS485 two wire is available as an option. The connection scheme is shown below:RS485 for multi-drop app

M390S Manual Operation  174.6 PID Tuning ConstantsThe PID tuning constants have been factory set for optimum performance and are noted below.Heating

M390S Manual Operation  18Typical Radiance temperature calibration look-up table (LUT) usedTo gain access to the custom look-up table:Refer to the 4

M390S Manual Operation  19Note: Calibration points do not have to be used as pre-programmed. To dial in adifferent calibration point, simply change

Confidential InformationThe material contained herein consists of information that is the property of LumaSenseTechnologies and intended solely for us

M390S Manual Operation  20To ensure consistent document formatting, this page was intentionally left blank.

M390S Manual Maintenance  215 Maintenance5.1 Cavity LifeThe life expectancy of the graphite cavity depends on the time and temperature of operation.

M390S Manual Maintenance  225.4 Furnace Core DisassemblyThe graphite core can be replaced without disconnecting cooling or purge tubing. Refer toexp

M390S Manual Maintenance  23Refer to the Appendix for an exploded view of the cavity assembly.5.5 Fuse LocationsThe M390 has several fuses. Refer t

M390S Manual Maintenance  245.6 CleaningClean the outside of the cabinet with mild soapy solution and water only. Do not attempt toclean the emitte

M390S Manual Index  25IndexCCavity life 21Cleaning 24Controller Calibration 17Controller Modes 14DDisposal 7EEurotherm iTools Software 17FFurnace Co

M390 Manual Index  26To ensure consistent document formatting, this page was intentionally left blank.

M390 Manual Appendix A: Drawings  27Appendix A: Drawings

M390 Manual Appendix A: Drawings  28

M390 Manual Appendix A: Drawings  29

M390S Manual Contents  iiiContents1 General Information ...

M390 Manual Appendix B: ASCII/BASIC  30Appendix B: ASCII/BASICTypical ASCII request string to read the blackbody temperature:'-------make a req

M390 Manual Appendix B: ASCII/BASIC  31A simple BASIC program to send blackbody setpoint:CLS'-----open comm port 1 for 9600 baud, 7,E,1-----OPE

M390 Manual Appendix C: Declaration of Conformance  32Appendix C: Declaration of Conformance

M390S Manual Contents  ivAppendix A: Drawings ...

M390S Manual General Information  51 General Information1.1 Information about the user manualCongratulations on choosing the high quality and highly

M390S Manual General Information  6Warning: DO NOT USE NITROGEN (N2) FOR PURGE GAS. AT HIGH TEMPERATURES,CYNIDE GAS COULD BE GENERATED.1.3 Limit of

M390S Manual General Information  7Return the instrument upon receipt of the RMA nµmber, transportation prepaid. Clearlyindicate the assigned RMA nµ

M390S Manual General Information  8To ensure consistent document formatting, this page was intentionally left blank.

M390S Manual Introduction  92 Introduction2.1 DescriptionThe M390 series are high temperature blackbody calibrators that can produce a very hightemp